Linux version 6.0.1 (olek@mocarz) (i686-buildroot-linux-uclibc-gcc.br_real (Buildroot 2022.05-1002-g1500b7d5c8) 12.1.0, GNU ld (GNU Binutils) 2.38) #6 Wed Oct 12 14:17:52 CEST 2022 KERNEL supported cpus: Intel GenuineIntel AMD AuthenticAMD Centaur CentaurHauls Transmeta GenuineTMx86 Transmeta TransmetaCPU x86/fpu: x87 FPU will use FXSAVE signal: max sigframe size: 1440 BIOS-provided physical RAM map: BIOS-e820: [mem 0x0000000000000000-0x000000000009f7ff] usable BIOS-e820: [mem 0x000000000009f800-0x000000000009ffff] reserved BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved BIOS-e820: [mem 0x0000000000100000-0x000000001efeffff] usable BIOS-e820: [mem 0x000000001eff0000-0x000000001eff2fff] ACPI NVS BIOS-e820: [mem 0x000000001eff3000-0x000000001effffff] ACPI data BIOS-e820: [mem 0x00000000fec00000-0x00000000ffffffff] reserved Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel! SMBIOS 2.3 present. DMI: WYSE V CLASS LE, BIOS Rev: 1.19 07/16/2009 tsc: Fast TSC calibration using PIT tsc: Detected 1200.022 MHz processor e820: update [mem 0x00000000-0x00000fff] usable ==> reserved e820: remove [mem 0x000a0000-0x000fffff] usable last_pfn = 0x1eff0 max_arch_pfn = 0x100000 x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT found SMP MP-table at [mem 0x000f3800-0x000f380f] initial memory mapped: [mem 0x00000000-0x01bfffff] ACPI: Early table checksum verification disabled ACPI: RSDP 0x00000000000F7970 000014 (v00 P4M80P) ACPI: RSDT 0x000000001EFF3040 00002C (v01 P4M80P AWRDACPI 42302E31 AWRD 00000000) ACPI: FACP 0x000000001EFF30C0 000074 (v01 P4M80P AWRDACPI 42302E31 AWRD 00000000) ACPI: DSDT 0x000000001EFF3180 004BDC (v01 P4M80P AWRDACPI 00001000 MSFT 0100000E) ACPI: FACS 0x000000001EFF0000 000040 ACPI: APIC 0x000000001EFF7DC0 000068 (v01 P4M80P AWRDACPI 42302E31 AWRD 00000000) ACPI: Reserving FACP table memory at [mem 0x1eff30c0-0x1eff3133] ACPI: Reserving DSDT table memory at [mem 0x1eff3180-0x1eff7d5b] ACPI: Reserving FACS table memory at [mem 0x1eff0000-0x1eff003f] ACPI: Reserving APIC table memory at [mem 0x1eff7dc0-0x1eff7e27] 0MB HIGHMEM available. 495MB LOWMEM available. mapped low ram: 0 - 1eff0000 low ram: 0 - 1eff0000 Zone ranges: DMA [mem 0x0000000000001000-0x0000000000ffffff] Normal [mem 0x0000000001000000-0x000000001efeffff] HighMem empty Movable zone start for each node Early memory node ranges node 0: [mem 0x0000000000001000-0x000000000009efff] node 0: [mem 0x0000000000100000-0x000000001efeffff] Initmem setup node 0 [mem 0x0000000000001000-0x000000001efeffff] On node 0, zone DMA: 1 pages in unavailable ranges On node 0, zone DMA: 97 pages in unavailable ranges Using APIC driver default ACPI: PM-Timer IO Port: 0x408 ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1]) ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) ACPI: Using ACPI (MADT) for SMP configuration information [mem 0x1f000000-0xfebfffff] available for PCI devices clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 pcpu-alloc: [0] 0 Built 1 zonelists, mobility grouping on. Total pages: 125870 Kernel command line: panic=30 printk.devkmsg=on Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) mem auto-init: stack:off, heap alloc:off, heap free:off Initializing HighMem for node 0 (00000000:00000000) Checking if this processor honours the WP bit even in supervisor mode...Ok. Memory: 479736K/507448K available (2316K kernel code, 3407K rwdata, 640K rodata, 15092K init, 1152K bss, 27712K reserved, 0K cma-reserved, 0K highmem) NR_IRQS: 2304, nr_irqs: 48, preallocated irqs: 16 Console: colour VGA+ 80x25 printk: console [tty0] enabled ACPI: Core revision 20220331 APIC: Switch to symmetric I/O mode setup Enabling APIC mode: Flat. Using 1 I/O APICs ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x114c307ac4a, max_idle_ns: 440795219360 ns Calibrating delay loop (skipped), value calculated using timer frequency.. 2400.04 BogoMIPS (lpj=12000220) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0 Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0 CPU: Centaur VIA Eden Processor 1200MHz (family: 0x6, model: 0xd, stepping: 0x0) Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization Spectre V2 : Kernel not compiled with retpoline Spectre V2 : Vulnerable Spectre V2 : Spectre v2 / SpectreRSB mitigation: Filling RSB on context switch Speculative Store Bypass: Vulnerable L1TF: Kernel not compiled for PAE. No mitigation for L1TF MDS: Vulnerable: Clear CPU buffers attempted, no microcode MMIO Stale Data: Unknown: No mitigations Performance Events: core: Welcome to zhaoxin pmu! no PMU driver, software events only. NMI watchdog: Perf NMI watchdog permanently disabled clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 256 (order: -1, 3072 bytes, linear) NET: Registered PF_NETLINK/PF_ROUTE protocol family thermal_sys: Registered thermal governor 'step_wise' thermal_sys: Registered thermal governor 'user_space' cpuidle: using governor ladder cpuidle: using governor menu PCI: PCI BIOS revision 2.10 entry at 0xf93b0, last bus=1 PCI: Using configuration type 1 for base access ACPI: Added _OSI(Module Device) ACPI: Added _OSI(Processor Device) ACPI: Added _OSI(3.0 _SCP Extensions) ACPI: Added _OSI(Processor Aggregator Device) ACPI: Added _OSI(Linux-Dell-Video) ACPI: Added _OSI(Linux-Lenovo-NV-HDMI-Audio) ACPI: Added _OSI(Linux-HPI-Hybrid-Graphics) ACPI: Actual Package length (8) is larger than NumElements field (2), truncated ACPI: Actual Package length (8) is larger than NumElements field (2), truncated ACPI: 1 ACPI AML tables successfully acquired and loaded ACPI: Interpreter enabled ACPI: PM: (supports S0 S5) ACPI: Using IOAPIC for interrupt routing PCI: Using host bridge windows from ACPI PCI: Using E820 reservations for host bridge windows ACPI: Enabled 7 GPEs in block 00 to 0F ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff]) acpi PNP0A03:00: _OSC: OS supports [Segments HPX-Type3] acpi PNP0A03:00: PCIe port services disabled acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge. PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000dffff window] pci_bus 0000:00: root bus resource [mem 0x1f000000-0xfebfffff window] pci_bus 0000:00: root bus resource [bus 00-ff] pci 0000:00:00.0: [1106:0314] type 00 class 0x060000 pci 0000:00:00.0: reg 0x10: [mem 0xf8000000-0xf9ffffff pref] pci 0000:00:00.1: [1106:1314] type 00 class 0x060000 pci 0000:00:00.2: [1106:2314] type 00 class 0x060000 pci 0000:00:00.3: [1106:3208] type 00 class 0x060000 pci 0000:00:00.4: [1106:4314] type 00 class 0x060000 pci 0000:00:00.7: [1106:7314] type 00 class 0x060000 pci 0000:00:01.0: [1106:b198] type 01 class 0x060400 pci 0000:00:01.0: supports D1 pci 0000:00:0b.0: [1106:3065] type 00 class 0x020000 pci 0000:00:0b.0: reg 0x10: [io 0xfc00-0xfcff] pci 0000:00:0b.0: reg 0x14: [mem 0xfdfff000-0xfdfff0ff] pci 0000:00:0b.0: supports D1 D2 pci 0000:00:0b.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:0f.0: [1106:0571] type 00 class 0x01018a pci 0000:00:0f.0: reg 0x20: [io 0xf800-0xf80f] pci 0000:00:0f.0: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] pci 0000:00:0f.0: legacy IDE quirk: reg 0x14: [io 0x03f6] pci 0000:00:0f.0: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] pci 0000:00:0f.0: legacy IDE quirk: reg 0x1c: [io 0x0376] pci 0000:00:10.0: [1106:3038] type 00 class 0x0c0300 pci 0000:00:10.0: reg 0x20: [io 0xf400-0xf41f] pci 0000:00:10.0: supports D1 D2 pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:10.1: [1106:3038] type 00 class 0x0c0300 pci 0000:00:10.1: reg 0x20: [io 0xf000-0xf01f] pci 0000:00:10.1: supports D1 D2 pci 0000:00:10.1: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:10.2: [1106:3038] type 00 class 0x0c0300 pci 0000:00:10.2: reg 0x20: [io 0xec00-0xec1f] pci 0000:00:10.2: supports D1 D2 pci 0000:00:10.2: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:10.3: [1106:3038] type 00 class 0x0c0300 pci 0000:00:10.3: reg 0x20: [io 0xe800-0xe81f] pci 0000:00:10.3: supports D1 D2 pci 0000:00:10.3: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:10.4: [1106:3104] type 00 class 0x0c0320 pci 0000:00:10.4: reg 0x10: [mem 0xfdffe000-0xfdffe0ff] pci 0000:00:10.4: supports D1 D2 pci 0000:00:10.4: PME# supported from D0 D1 D2 D3hot D3cold pci 0000:00:11.0: [1106:3227] type 00 class 0x060100 HPET not enabled in BIOS. You might try hpet=force boot option pci 0000:00:11.5: [1106:3059] type 00 class 0x040100 pci 0000:00:11.5: reg 0x10: [io 0xe400-0xe4ff] pci 0000:00:11.5: supports D1 D2 pci_bus 0000:01: extended config space not accessible pci 0000:01:00.0: [1106:3344] type 00 class 0x030000 pci 0000:01:00.0: reg 0x10: [mem 0xf4000000-0xf7ffffff pref] pci 0000:01:00.0: reg 0x14: [mem 0xfb000000-0xfbffffff] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] pci 0000:01:00.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff] pci 0000:01:00.0: supports D1 D2 pci 0000:00:01.0: PCI bridge to [bus 01] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff] pci 0000:00:01.0: bridge window [mem 0xfb000000-0xfcffffff] pci 0000:00:01.0: bridge window [mem 0xf4000000-0xf7ffffff pref] pci_bus 0000:00: on NUMA node 0 ACPI: PCI: Interrupt link LNKA configured for IRQ 10 ACPI: PCI: Interrupt link LNKB configured for IRQ 3 ACPI: PCI: Interrupt link LNKC configured for IRQ 5 ACPI: PCI: Interrupt link LNKD configured for IRQ 11 ACPI: PCI: Interrupt link LNKE configured for IRQ 11 ACPI: PCI: Interrupt link LNKF configured for IRQ 0 ACPI: PCI: Interrupt link LNKF disabled ACPI: PCI: Interrupt link LNK0 configured for IRQ 0 ACPI: PCI: Interrupt link LNK0 disabled ACPI: PCI: Interrupt link LNK1 configured for IRQ 0 ACPI: PCI: Interrupt link LNK1 disabled ACPI: PCI: Interrupt link ALKA configured for IRQ 20 ACPI: PCI: Interrupt link ALKA disabled ACPI: PCI: Interrupt link ALKB configured for IRQ 21 ACPI: PCI: Interrupt link ALKC configured for IRQ 22 ACPI: PCI: Interrupt link ALKD configured for IRQ 23 ACPI: PCI: Interrupt link ALKD disabled PCI: Using ACPI for IRQ routing PCI: pci_cache_line_size set to 64 bytes e820: reserve RAM buffer [mem 0x0009f800-0x0009ffff] e820: reserve RAM buffer [mem 0x1eff0000-0x1fffffff] clocksource: Switched to clocksource tsc-early pnp: PnP ACPI init pnp 00:00: disabling [mem 0x000d2000-0x000d3fff] because it overlaps 0000:01:00.0 BAR 6 [mem 0x000c0000-0x000dffff] system 00:00: [mem 0x000f0000-0x000f7fff] could not be reserved system 00:00: [mem 0x000f8000-0x000fbfff] could not be reserved system 00:00: [mem 0x000fc000-0x000fffff] could not be reserved system 00:00: [mem 0x1eff0000-0x1effffff] could not be reserved system 00:00: [mem 0xffff0000-0xffffffff] has been reserved system 00:00: [mem 0x00000000-0x0009ffff] could not be reserved system 00:00: [mem 0x00100000-0x1efeffff] could not be reserved system 00:00: [mem 0xfec00000-0xfec00fff] could not be reserved system 00:00: [mem 0xfee00000-0xfee00fff] has been reserved system 00:00: [mem 0xfff80000-0xfffeffff] has been reserved system 00:01: [io 0x0400-0x047f] has been reserved system 00:01: [io 0x0500-0x050f] has been reserved system 00:02: [io 0x04d0-0x04d1] has been reserved system 00:02: [io 0x0800-0x087f] has been reserved system 00:02: [io 0x0880-0x08ff] has been reserved system 00:02: [io 0x0290-0x0297] has been reserved pnp 00:05: [dma 3] pnp: PnP ACPI: found 6 devices clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns NET: Registered PF_INET protocol family IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear) Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) TCP bind hash table entries: 4096 (order: 2, 16384 bytes, linear) TCP: Hash tables configured (established 4096 bind 4096) UDP hash table entries: 256 (order: 0, 4096 bytes, linear) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) pci 0000:00:01.0: PCI bridge to [bus 01] pci 0000:00:01.0: bridge window [io 0xd000-0xdfff] pci 0000:00:01.0: bridge window [mem 0xfb000000-0xfcffffff] pci 0000:00:01.0: bridge window [mem 0xf4000000-0xf7ffffff pref] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000dffff window] pci_bus 0000:00: resource 7 [mem 0x1f000000-0xfebfffff window] pci_bus 0000:01: resource 0 [io 0xd000-0xdfff] pci_bus 0000:01: resource 1 [mem 0xfb000000-0xfcffffff] pci_bus 0000:01: resource 2 [mem 0xf4000000-0xf7ffffff pref] pci 0000:00:01.0: disabling DAC on VIA PCI bridge ACPI: \_SB_.PCI0.ALKB: Enabled at IRQ 21 pci 0000:00:11.0: Bypassing VIA 8237 APIC De-Assert Message PCI: CLS 32 bytes, default 64 workingset: timestamp_bits=30 max_order=17 bucket_order=0 i8042: PNP: No PS/2 controller found. i8042: Probing ports directly. serio: i8042 KBD port at 0x60,0x64 irq 1 sched_clock: Marking stable (765512631, -6118773)->(758355007, 1038851) Freeing unused kernel image (initmem) memory: 15092K Write protecting kernel text and read-only data: 2960k Run /init as init process with arguments: /init with environment: HOME=/ TERM=linux NET: Registered PF_UNIX/PF_LOCAL protocol family tsc: Refined TSC clocksource calibration: 1200.042 MHz clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x114c4366452, max_idle_ns: 440795242977 ns clocksource: Switched to clocksource tsc softdog: initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=1) softdog: soft_reboot_cmd= soft_active_on_boot=0 io scheduler mq-deadline registered lp: driver loaded but no devices found Non-volatile memory driver v1.3 ACPI: bus type USB registered usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ehci-pci 0000:00:10.4: EHCI Host Controller ehci-pci 0000:00:10.4: new USB bus registered, assigned bus number 1 ehci-pci 0000:00:10.4: irq 21, io mem 0xfdffe000 ehci-pci 0000:00:10.4: USB 2.0 started, EHCI 1.00 hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected vt1211: Found VT1211 chip at 0x6000, revision 2 hwmon_vid: Using 6-bit VID table for VIA Eden CPU vt1211 vt1211.24576: hwmon_device_register() is deprecated. Please convert the driver to use hwmon_device_register_with_info(). rtc_cmos 00:03: RTC can wake from S4 rtc_cmos 00:03: registered as rtc0 rtc_cmos 00:03: alarms up to one year, y3k, 242 bytes nvram Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled 00:04: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A usb 1-1: new high-speed USB device number 2 using ehci-pci parport_pc 00:05: reported by Plug and Play ACPI parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA] lp0: using parport0 (interrupt-driven). SCSI subsystem initialized libata version 3.00 loaded. pata_via 0000:00:0f.0: version 0.3.4 ACPI: \_SB_.PCI0.ALKA: Disabled and referenced, BIOS bug ACPI: \_SB_.PCI0.ALKA: Enabled at IRQ 20 scsi host0: pata_via scsi host1: pata_via ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xf800 irq 14 ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xf808 irq 15 ata1.00: CFA: 128MB ATA Flash Disk, AD B612J, max UDMA/66 ata1.00: 250112 sectors, multi 0: LBA ata1.00: limited to UDMA/33 due to 40-wire cable scsi 0:0:0:0: Direct-Access ATA 128MB ATA Flash 612J PQ: 0 ANSI: 5 uhci_hcd: USB Universal Host Controller Interface driver uhci_hcd 0000:00:10.0: UHCI Host Controller uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 2 uhci_hcd 0000:00:10.0: irq 21, io port 0x0000f400 watchdog: watchdog0: nowayout prevents watchdog being stopped! watchdog: watchdog0: watchdog did not stop! hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected uhci_hcd 0000:00:10.1: UHCI Host Controller uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3 uhci_hcd 0000:00:10.1: irq 21, io port 0x0000f000 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected uhci_hcd 0000:00:10.2: UHCI Host Controller uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4 uhci_hcd 0000:00:10.2: irq 21, io port 0x0000ec00 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected uhci_hcd 0000:00:10.3: UHCI Host Controller uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 5 uhci_hcd 0000:00:10.3: irq 21, io port 0x0000e800 hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected via-rhine 0000:00:0b.0 eth0: VIA Rhine III at (ptrval), 00:80:64:96:19:0a, IRQ 19 via-rhine 0000:00:0b.0 eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link c5e1 videodev: Linux video capture interface: v2.00 usb 1-1: Found UVC 1.00 device (046d:0825) input: UVC Camera (046d:0825) as /devices/pci0000:00/0000:00:10.4/usb1/1-1/1-1:1.0/input/input0 usbcore: registered new interface driver uvcvideo usb 1-1: set resolution quirk: cval->res = 384 usbcore: registered new interface driver snd-usb-audio sd 0:0:0:0: [sda] 250112 512-byte logical blocks: (128 MB/122 MiB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes sd 0:0:0:0: [sda] Attached SCSI disk ACPI: \_SB_.PCI0.ALKC: Enabled at IRQ 22 input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1 ACPI: button: Power Button [PWRB] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2 ACPI: button: Sleep Button [SLPB] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3 ACPI: button: Power Button [PWRF] input: PC Speaker as /devices/platform/pcspkr/input/input4 Warning: Processor Platform Limit event detected, but not handled. Consider compiling CPUfreq support into your kernel. random: crng init done NET: Registered PF_PACKET protocol family usb 1-1: reset high-speed USB device number 2 using ehci-pci